• Novinka

Curtain modul - ovladač stínění, WiFi TASMOTA

Modul pro ovládání motoru stínění s WiFi a softwarem TASMOTA.

412,00 Kč

vč. ekologické daně 1,50 Kč

Vč. DPH
Počet
Skladem u nás >5ks

 

Nákupem podpoříte projekt TASMOTA

 

Možnost vrácení zboží 14 dní

 

Rychlá doprava

 

Bezpečný obchod

 

Zkontrolujte si cenu dopravy

Curtain modul - ovladač stínění, WiFi TASMOTA

  

Modul pro ovládání motoru stínění se softwarem TASMOTA a WiFi komunikací.

    

Poslední verze TASMOTY

Plně kompatibilní s oficiálním OTA server

Software TASMOTA je zaveden při výrobě

Využívá ESP8285 chip s 2M flash

 

Úplné místní ovládání. 

Jedná se komplikovanější modul a nedoporučujeme ho méně zkušeným zájemcům. Modul se musí pro reálné nasazení kalibrovat podle popisu v dolní časti textu.

   

Parametry:

Chipset: ESP8285

Napájení: AC 100-250V, (50/60Hz)

Komunikace: WiFi, 2.4GHz

Rozměry: (Š)46*(V)46*(H)18,6mm

Barva: Bílá

Pracovní vlhkost okolí: 5%-95%

Pracovní teplota: ﹣20℃-50℃

Potřeba serveru: ne

Firmware: TASMOTA

Výrobce: athom.tech

   

    

Tasmota Template:

{"NAME":"Athom Curtain Module","GPIO":[0,0,0,160,161,32,0,0,224,576,225,0,0,0],"FLAG":0,"BASE":18,"CMND":"SO80 1;ShutterMode 1;SwitchDebounce 300;ButtonDebounce 300"}

    

GPIOs:

GPIO0 None

GPIO1 None

GPIO2 None

GPIO3 LedLinki

GPIO4 Switch1

GPIO5 Button1

GPIO9 None

GPIO10 None

GPIO12 Relay1

GPIO13 Switch2

GPIO14 Relay2

GPIO15 None

GPIO16 None

GPIO17 None

FLAG None

   

Calibration

Kalibraci jsme zatím v našem obchodě neprováděli. Jedná se o komplikovanější činnost a při překladu jsme získali dojem, že bez znalosti vlastního procesu bychom mohli popis zkreslit nebo učinit nesrozumitelný. Proto tuto část popisu nepřekládáme do češtiny. Je také uveden odkaz na anglické stránky dokumentace TASMOTA, kde je proces kalibrace popsán.    

  • Start your shutter in a closed position preferably. Set internal position to closed with ShutterSetClose<x>.
  • Set the time needed to open the shutter completely with ShutterOpenDuration<x>.
  • If the shutter opens more than needed, move it to the desired position with ShutterSetPosition<x> then set the position to fully open (100) with ShutterSetOpen<x> and decrease the open time.
  • Set the time needed to close the shutters with ShutterCloseDuration<x>.
  • If the shutter does not close completely, open again and adjust close time.
  • If it runs too long, move it back to desired closed position with ShutterSetPosition<x>, reset to 0 with ShutterSetClose<x> and decrease open time.
  • Alternate between opening and closing the shutter until you find out the exact times needed to get the same positions multiple times
  • Now set the 50% open position of the shutter. Some shutters need some time from totally closed until they begin moving the bottom-most part and opening. This often results in a shutter that is less than 50% open when the shutter has been operating for 50% of the set time. This can be corrected by using ShutterSetHalfway<x>. Use this procedure to calibrate the half-open position:
  • ShutterClose<x> (confirm that the shutter is completely closed)
  • ShutterSetHalfway<x> 50 (reset to default)
  • Move the shutter to actual 50% open position.
  • Use ShutterPosition<x> to inquire the shutter's current position and record the value. This value is a percentage of the total opening (e.g., 63 = 63% of opening).
  • ShutterClose<x>
  • ShutterSetHalfway<x> 63 (using the value from step #4 above)
  • Restart 1

After calibration is complete, you might want to enable an additional 1 second motor movement with ShutterEnableEndStopTime<x> 1 when the shutter is asked to move to its end positions (0% and 100%). With this you can guarantee that end positions are still reached in case of inaccuracies. Take care to disable this with ShutterEnableEndStopTime<x> 0 before further open or close duration measurements.

    

 For more information:  https://tasmota.github.io/docs/Blinds-and-Shutters/#calibration

    

Notice:

If the curtain module working automatically without operation, please type demand line:

SwitchDebounce 300;ButtonDebounce 300

KM01-TAS
9 ks

Parametry

Kryt:
plast
Barva:
bílá
Rozměry:
46 x 46 x 18,6
Kanály:
1
Napájecí napětí:
100 - 250 V, AC 50-60Hz
Wifi:
2.4GHz, 802.11 b/g/n
Zátěž:
Výrobce neuvádí
Potřeba serveru:
ne
Pracovní teplota:
-20℃ až +50℃
Vlhkost okolí:
5% - 95% RH
Požární ochrana:
94-V0
Firmware:
TASMOTA
Výrobce:
athom.tech
Chipset:
ESP8285
Komentáře (0)
Na tento produkt momentálně není přidána žádná recenze.